July
20, 2010
Service
Instructions
(not available for download)
| # |
Content |
Date
of Issue |
| SI
3 |
Instruction for low-pitch-stop, high-pitch-stop and full-reverse-stop adjustment on MTV-Propellers (former AAW-003a) | March
14, 2000 |
| SI
4D |
De-Ice Boots, Wiring and Installation | Okt.
12 , 2009 |
| SI
6 |
Removal and Installation of Servo Motors at electrically controlled MTV-Propellers (former AAW-006) | March
14, 2000 |
| SI
7 |
Installation of Clamp Type Counterweights at MTV-Propellers | March
14, 2000 |
| SI
16 |
Installation of new counterweights | Oct
17, 2000 |
| SI
17A |
Change of minimum blade pitch on counterweighted MTV-Propellers | Jan
16, 2006 |
| SI
18C |
Airpressure Switch Adjustment for Propellers with Reverse Thrust Capability | Oct
12, 2005 |
| SI
20 SI 20-1 |
Drehzahlsensor
und deren Tauschverfahren RPM Sensors and the Replacement Procedures |
July
31, 2002 |
| SI
22 |
Removal and Installation of the Stainless Steel Seal inserts in modified MTV-hubs | Dec
17, 2001 |
| SI
23A |
Installation of New Type of Blade Seals in Constant Speed MTV-Propellers | Jan
29, 2004 |
| SI
24* |
Removal of Front Cover for Maintenance or Modification Purposes | June
21, 2002 |
| SI
25B |
Replacement of Servo Motors by "MT P820-()" Servo Motors | Feb
1, 2005 |
| SI
27 |
Modification
of the "Sleeve Valve Spring" installed in P-480-( ) Propeller Governors |
July
17, 2002 |
| SI
28A |
Setting
Maximum Blade Pitch on MT-Propellers (which use oil pressure to increase pitch) |
Jan
16, 2006 |
| SI
29 SI 29-1 |
Bushing threads conversion on SAE No. 2 Flange type | Jan
16, 2004 |
SI
30 |
Adjustment of Relief Valve Pressure on P-41()-(), P-42()-() and P-44()-() Governors | June
26, 2003 |
SI
31* |
Application
of Blade Bearing Grease to a MTV-25-2-D-C-R(M)/CFR170-23 |
Nov
03, 2003 |
SI
33 |
Entfernen
des Safety Lock bei MTV-6-A-C-F für DA42 |
April
27, 2004 |
SI
34 |
Piston Extension Replacement MTV-6 | July
05, 2004 |
SI
35 |
Additonal Erosion Protection on a special flying boat | Aug
13, 2004 |
SI
36 |
Replacement of 3 counterweights on new MT-Propeller | Oct
26, 2004 |
| SI
37A |
Bonding
of self adhesive PU-Erosion strip on MT-Propellers with Metal Erosion
Sheet (replaces E-482 of April 14, 1994 of same contents) |
April
05, 2005 |
SI
39 |
Blade installation for in-field removable MT-Propeller aluminum blades MTV-27-2 | Aug
26, 2005 |
SI
40A |
Oil capacity reduction plugs in the propeller hub of the propeller model MTV-9-B-S/198-58B with the engine SMA SR-305-230 | March
23, 2009 |
SI
41 |
Flange Stud Replacement on MT-Propeller with D-flange (ARP 502) | Dec
19, 2005 |
| SI 44 | Flange Stud Replacement on MT-Propeller with A-type flange | April
13, 2007 |
| SI 45A | Governor Lever
Exchange MTP Governors P-8()()-() and P-9()()-() series |
June
25, 2007 |
| SI 46 | Work Instruction
for the In-Field Final Assembly of MTV-16-1-N-C-F-R(P)/CFRLD280-65 Propeller |
Okt.
17, 2007 |
| SI 47 | Opening of Propeller Front Cover of MT-Propellers without Counterweights and without Feathering and Reversing Capability | Oct.
17, 2007 |
| SI 48C* | Conversion from A- to R- Flange | April
27, 2010 |
| SI 49 | Removal and Installation of Repair Bushing A-1251-X on hydraulic feathering propellers | Oct.
16, 2008 |
| SI 50 | Removal and Installation of preload ring A-027-C on MTV-6-A | Oct.
20, 2008 |
| SI 51* | Installation
of Stainless Steel Plates on Aircraft Fuselage on Dornier DO-228-( ) with MTV-27-( ) |
Dec.
03, 2008 |
| SI 53 | Turning Connection
Plug of Electric MT-Propeller Governor P-8( )3-( ) and P-8( )7-( ) |
April
07, 2009 |
| SI 54 | Propeller Governors for
electricf Control P-8( )7 Series Adjustment of maximum Governing Speed Stop |
Aug
21, |
*These Service Instructions may be distributed on request only
(Please
report any bugs or suggestions to: support@mt-propeller.com
)
©
2008 Webdesign
by Planet-Faraway